2011-2013 TVS Roushcharged Mustang Performance Package Upgrade
If you have a 2011-2013 TVS Roushcharged Mustang and are looking for more power and performance then look no further!!
JDM Engineering has put together a Roush Mustang Performance Package that will add 100 Horsepower and over 120 foot pounds of TORQUE to you 2011-2013 Roush Mustang! This kit is tested and developed in house on Team JDM's Roush Stage 3 Mustang equipped with the TVS Roushcharger. Hundreds of dyno pulls and quarter mile runs along with thousands of hours in JDM Custom Tuning Development have brought us to this incredible power, performance increase for your 2011-2013 Roushcharged Mustang.
JDM Engineering's James D'Amore will build a custom tune file for your 2011-2013 Roushcharged Mustang and load it on to the SCT XCAL3 flash device specifically for your vehicle. An 82mm Supercharger Pulley and shorter belt are included to raise boost levels on your Roushcharger up 3 psi over stock ! Colder Spark plugs M-12405-M50 are included to help fight off detonation and spark blow out from the extra boost pressure and heat generated by the smaller pulley. Finally, a Roush Cold Air Intake Kit 421529 is included to increase the air flow to the Roushcharger. This complete 2011-2013 Roushcharged Mustang 650 HP performance-power package will yield nearly 575 rwhp without any other modifications !!
With the addition of a Larger Throttle Body and Higher Flowing Exhaust, horsepower levels as high as 600 rwhp have been seen in testing !! For more information about other parts to add more power, check out our 2011-2013 Mustang sections or give TeamJDM a call at 732-780-0770
Run like Pro's with JDM Engineering
The 2011-2013 Roushcharger Mustang 650 HP Peformance UPgrade Power Package Includes :
- SCT XCAL3 Flash Device with JDM's custom Tune
- Roush Cold Air Kit-421529
- Gates Belt K060810
- Ford Racing 0 Degree Spark Plugs M-12405-M50
2011-2013 JDM Engineering Roush TVS Mustang 650 HP Upgrade Kit (Stock/Modified Comparison)
- -Stock Roush Kit = 540HP (475RWHP)
- -Stock Boost Level is 7-8PSI
- -Modified Using JDM Engineering Roush TVS Upgrade 650HP/600TQ = 575RWHP/525TQ 100HP+ Gain!!
- -Modified Kit Produces 11-12PSI of Boost with 82mm Pulley!!
The 2011-2013 Roushcharger Mustang 650 HP Upgrade Kit Power Package fits:
- 2011 — 2014 Roushcharged Mustang
Please send your completed tune sheet at your earliest convenience to: firstname.lastname@example.org so we can commence your order. If you need any help filling out your tune sheet please feel free to email: email@example.com or call 732-780-0770
Important parts and tuning notice:
By ordering this tune, you agree to assume all responsibility for assuring that it is to be used for off-road and/or competition use only and is not to be used on a vehicle that is registered for use on public roads nor highways.
IT IS OUR POLICY TO NOT DISABLE ANY FEDERALLY MANDATED EMISSIONS EQUIPMENT NOR MONITORS ON ANY VEHICLE WITH A VEHICLE IDENTIFICATION NUMBER (VIN). IT IS A FEDERAL OFFENSE FOR US TO DO SO.
Because U.S., Canadian, and other international, state or provincial laws and regulations may prohibit removal or modification of components that were installed on vehicles by Ford Motor Company to meet emission requirements or to comply with motor vehicle safety regulations applicable to vehicles manufactured for use on public roads, JDM Engineering wants you to know the following:
Most of the parts and services offered in this online catalog are for off-road use or competition use only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this off-road or race use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assume all associated risk of the purchase.
Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. JDM Engineering assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of our products or services. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
The emissions laws and regulations of the state of California apply to all non-racing vehicles. Consequently, some parts in this catalog may legally be used in California only on a racing vehicle which will never be operated on public roads.
- 18.00 (in)
- 13.00 (in)
- 13.00 (in)