2007-2014 Shelby GT500 800HP Whipple 2.9L GEN 3 Supercharger Upgrade
JDM Engineering's 2007-2014 Shelby GT500 800HP Whipple 2.9L GEN 3 Supercharger Upgrade Kit is a complete, turn-key package ready to make 800HP on your 5.4L/5.8L 4V engine. The kit comes with a Whipple 2.9L Supercharger with Crusher inlet WK-2500TB and a 3.00" pulley. This blower comes geared for 17-18 PSI boost which is a safe when using premium 91-93 octane pump gas. JDM includes a custom tune by James D'Amore loaded on an SCT Xcal 4 Flash Device. For improved air flow and mass airflow sensor range, a JLT 123mm Cold Air Intake is included as well as the Ford Racing twin 65mm Throttle Body. Bosch 72lb injectors are used to keep up with the fuel demand at these power levels. Because the 72lb injectors are stock height the fit perfectly under the fuel rails with no bulky spacers. Finally, we include a set of 2 degree colder than stock spark plugs which will help remove heat from the cylinders and prevent detonation.
With these parts, your 2007-2014 Shelby GT500 will make approximately make up to 700+ HP at the tires which translates to 800+ at the engine and 650lb-ft of torque!
*The 2.9L Whipple Supercharger is also not any taller than stock so it fits under aftermarket strut tower braces and the Factory Ford hood.
**Comes in Black Powdercoat, Polished, or Ford Blue. Choose your option at check out. Polish or Ford Blue will add $600.00 at check out.
**Fix shipping charges apply to the lower US 48 sates only. Please contact us directly for HI, AK and international shipping arrangements.
- Up to 700+ HP at the tires / 800+ @ the engine
- 650lb-ft torque
- Increase in Horse Power and Torque
- Better Drivability
- Whipple 2.9L GEN 3 Supercharger WK-2500TB
- Whipple Crusher Inlet Elbow
- Ford Racing Twin 65mm Cobra Jet Throttle Body M-9926-CJ65
- 3.00" Supercharger Pulley: 17-18 PSI Boost
- JLT 123mm Cold Air Intake
- 72LB. Injectors
- NGK TR6 Spark Plugs
- SCT X4 with JDM Engineering Custom Tune
PLEASE ALLOW 6 TO 8 WEEKS FOR WHIPPLE BUILD
Please send your completed tune sheet at your earliest convenience to: email@example.com so we can commence your order. If you need any help filling out your tune sheet please feel free to email: firstname.lastname@example.org or call 732-780-0770
Please allow 10-15 business days for your tuner to be shipped and is subject to change due to high demand and race season.
Important parts and tuning notice:
By ordering this tune, you agree to assume all responsibility for assuring that it is to be used for off-road and/or competition use only and is not to be used on a vehicle that is registered for use on public roads nor highways.
IT IS OUR POLICY TO NOT DISABLE ANY FEDERALLY MANDATED EMISSIONS EQUIPMENT NOR MONITORS ON ANY VEHICLE WITH A VEHICLE IDENTIFICATION NUMBER (VIN). IT IS A FEDERAL OFFENSE FOR US TO DO SO.
Because U.S., Canadian, and other international, state or provincial laws and regulations may prohibit removal or modification of components that were installed on vehicles by Ford Motor Company to meet emission requirements or to comply with motor vehicle safety regulations applicable to vehicles manufactured for use on public roads, JDM Engineering wants you to know the following:
Most of the parts and services offered in this online catalog are for off-road use or competition use only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this off-road or race use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assume all associated risk of the purchase.
Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. JDM Engineering assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of our products or services. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
The emissions laws and regulations of the state of California apply to all non-racing vehicles. Consequently, some parts in this catalog may legally be used in California only on a racing vehicle which will never be operated on public roads.
- 100.00 LBS
- 48.00 (in)
- 36.00 (in)
- 18.00 (in)